Great-planes 38% Extra 330S ARF - GPMA1290 Manuale Utente

Great Planes® Model Manufacturing Co. guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warra

10❏ 2. Using the nylon straps as a guide, drill 3/32" [2.4mm] holes for the mounting screws. Mount the tail gear in the fuselage with the straps

11NOW THE WHEELS…Refer to the illustration while mounting the wheels.Flat Spot#8 Flat Washer3/16" [4.8mm]Wheel Collars6-32 x 1/4" [6.4mm]SHC

12❏ 4. Mount the aluminum tail wheel arm where shown by drilling 1/16" [1.6mm] holes for the three #2 x 3/8" [10mm] mounting screws—don’t fo

13Refer to the following photo to fi nish mounting the rudder servos.90°❏ 5. Same as was done for the aileron and elevator servo wheels, drill the hole

❏ 4. Guide the cables through the slots in the fuselage and temporarily connect the pin clevises to the horns on the rudder.❏ 5. Use masking tape to t

1515Hook Up the ThrottleRefer to these photos of the completed throttle servo installation while hooking up the throttle.Throttle Servo Mount Guide Tu

16end of the two short tubes. The tubing is pretty hard, so use a block of wood with a 5/32" [4mm] hole drilled in it to bend the vent tube. Conn

17nylon tie straps (not included). In addition to hook and loop or tie straps, use adhesive foam mounting tape to cushion the module and to keep it fr

18Refer to this photo while fi nishingthe rest of the radio installation.❏ 2. Glue the plywood receiver tray mount doublers to the bottom of the side s

19Mount the Cowl❏ 1. Use manilla folder material or thin cardstock to make templates for the bottom two cowl mounting screws. Tape the templates to th

2TABLE OF CONTENTSINTRODUCTION ... 2SAFETY PRECAUTIONS ...

20❏ 9. Remove the muffl ers. Mount the cowl to the fuselage. Use a fi ne-point felt-tip pen to mark the holes for the exhaust pipe cutouts directly onto

21(Move the ruler forward)❏ 3. Defl ect the control surface and move your ruler forward so it will be contacting the trailing edge. Read the measureme

22❏ 3. Using an assistant, lift the model with the C.G. cradles under the tips of the wings with screwdrivers in the middle holes that are marked 5.7

23ENGINE SAFETY PRECAUTIONSFailure to follow these safety precautions may result in severe injury to yourself and others.• Keep all engine fuel in a

24CHECK LISTDuring the last few moments of preparation your mind may be elsewhere, anticipating the excitement of the fi rst fl ight. Or you may be stay

25Double-check the control directions before every fl ight. And for the fi rst fl ight, takeoff on low rates. Remember to takeoff into the wind, point th

26RUDDER PUSHROD ASSEMBLYELEVATOR SERVO EXTENSIONS90mm 90mm 90mmMake the servo extensions this way if connectingthe elevator servos to separate channe

273D FLYINGBecause of the power to weight ratio on 3D planes, straight and level fl ight should be at a reduced throttle and full power should only be

TORQUE ROLLThis is the same as the vertical hover but without the use of right aileron to keep the model from rolling. If needed, you can use a little

3PROTECT YOUR MODEL, YOURSELF & OTHERS...FOLLOW THESE IMPORTANT SAFETY PRECAUTIONS1. Your 38% Extra 330S ARF should not be considered a toy, but

Other Radio GearThe following servo extensions were used on the model in the instruction manual:Note: If using digital servos, be certain to use servo

Replacement parts for the Great Planes 38% Extra 330S ARF are available using the order numbers in the Replacement Parts List that follows. The fastes

666SHRINK THE COVERING❏ 1. Where necessary, use a covering iron (set to approximately 250°F [120°C] with a covering sock to go over any parts of the m

7❏ 5. Connect a 12" [305mm] servo extension (HCAM2711 for Futaba) to one of the aileron servos and 36" [915mm] servo extension (HCAM2726 for

8Scratch a small arrowonto the servo wheelso you will know whichway is forward.❏ 3. Once the correct orientation of the servo wheel has been determine

9Cotter PinPin Washer❏ 11. While you have your wings on your workbench and the servos operating, you could go ahead and set the control throws as indi